Yamaha Blaster 200
 |
|
CT Sonic Yamaha Blaster Cylinder Kits At this time the CT Sonic Aftermarket cylinders are discontinued. We are still building cylinders based off of the stock cylinder. The owner of the foundry that poured our castings for us passed on, and without our knowledge all of his tooling was given of sold to another foundry. At this time we have not located our tooling. If we locate the tooling we will build them again, but for now we are out of production. The Yamaha Blaster CT Sonic cylinder has proven to be the highest output cylinder available for the Blaster. The cylinder was designed from top to bottom to make big horsepower over a wide power curve. The Sonic cylinder uses Honda CR250 reed cage to maximize flow and output. The cylinder also has a 3 port auxiliary exhaust port design, like nearly every current model 2 stroke MX bike design. The Sonic cylinder kits are available in two basic packages: 200cc to meet AMA youth race rules and the unrivaled 240cc big bore package. The 200cc cylinder utilizes and aluminum sleeve and Nikasil plating to offer maximum cooling under race conditions. We are just now releasing a new batch of the CT Sonic Blaster Cylinders. We have upgraded to a billet aluminum Head, available in black or blue anodized, or just billet aluminum. |
|
CT Sonic 200cc Yamaha Blaster Motor Package…… The kit includes: New Sonic cylinder, CT porting, head, piston kit, wrist pin bearing, reed cage, intake boot, and top-end gasket set. |
| CT Sonic 200cc Yamaha Blaster Complete Package…… The kit includes: New Sonic cylinder, CT porting, head, piston kit, wrist pin bearing, reed cage, intake boot, Keihin 36mm PWK pre-jetted carburetor, cable, CT pipe and silencer, and top-end gasket set. |
|
CT Sonic 240cc Big Bore Yamaha Blaster Motor Package……$ The kit includes: New Sonic big bore cylinder, CT porting, head, big bore piston kit, wrist pin bearing, reed cage, intake boot, and top-end gasket set. |
| CT Sonic 240cc Big Bore Yamaha Blaster Complete Package…… The kit includes: New Sonic big bore cylinder, CT porting, head, piston kit, wrist pin bearing, reed cage, intake boot, Keihin 36mm PWK or Keihin 38mm PWK Air Striker pre-jetted carburetor, cable, CT pipe and silencer, and top-end gasket set. |
| Stock Cylinder Kits |
|
Yamaha Blaster Porting Package……$549.00 : Not only does this kit boost up your HP a significant amount it also retains great reliability, along with freshening up your complete top end. This kit will run well off of the stock carb., but makes even more HP with a larger carb. This kit will require a good aftermarket pipe, to gain its full potential. The kit includes CT porting, head re-chambering, Boring or honing the cylinder to fit a new piston, new piston kit, wrist pin bearing, and top-end gasket set. |
| 240cc Big Bore Yamaha Blaster Motor Package……$799.00 The kit includes: Re-sleeving your cylinder with a big bore sleeve, CT porting, head re-chambering, modified big bore piston kit, and top-end gasket set. This kit is for the customers that already have a pipe and carburetor. This kit is for the stock Blaster cylinder. This kit price is for you shipping us your cylinder and head. |
|
240cc Big Bore Yamaha Blaster Complete Package……$1479.00 The kit includes: Re-sleeving your cylinder with a big bore sleeve, CT porting, head re-chambering, modified big bore piston kit, Keihin 35mm PWK pre-jetted carburetor, air box adapter tube, throttle cable, TDR reeds, CT Sonic pipe and silencer and top-end gasket set. This kit is for the stock Blaster cylinder. This kit price is for you shipping us your cylinder and head. |
| PLEASE NOTE: Your head is returned assembled and ready to bolt on and run. This kit price is for you shipping us your top-end only. If you would like to ship us your complete motor, add $250.00 for R&R of top-end. |
| CLICK Here for Shipping Instructions for Your Motor |
| Description | Price | Photo |
 |
||
| Yamaha Blaster MX Pipe and Silencer | $549.95 |
 |
| Yamaha Blaster Silencer – Fits CT Racing Pipe. | $166.95 | |
 |
||
| Cylinder Bore and Chamfer Ports | $100.00 | |
| Port, Deck, and Re-Chamber Head | $325.00 | |
| Crankshaft Rebuild (Labor Only) | $95.00 | |
 |
||
| Dura Blue Foam Air Filter – Fits stock airbox. | $38.97 |
 |
| K&N Air Filter – Fits stock airbox. | |
 |
| Outerwear Pre-filter – Fits K&N Air Filter YA-2088. | $16.95 |
 |
 |
||
| Yamaha Blaster Pro-X Piston Kit– Available in 66, 66.25, 66.50, 66.75, 67, 67.25, 67.50, 67.75, or 68mm | $89.87 |
 |
| Yamaha Blaster Wiseco Piston Kit – Available in 66, 66.25, 66.50, 66.75, 67, 67.25, 67.50, 67.75, 68, or 68.25mm | $111.95 |
 |
| Yamaha Blaster Wossner Piston Kit – Available in 66, 66.25, 66.50, 66.75, 67, 67.50, 68, 68.5, and 69mm | |
 |
| Yamaha Blaster Wossner Piston Kit CT Sonic 240cc Big Bore – Available in 72, 72.25, 72.50, or 73mm | $194.95 |
|
| Cometic Top-end Gasket Set – Available in 68mm (200cc stock cylinder), 68.25mm (200cc CT Sonic cylinder), 72.5mm (240cc big bore stock cylinder), and 73mm (240cc CT Sonic cylinder) | $37.52 |
 |
| Winderosa Complete Gasket Set – This complete engine gasket set also includes all of the engine oil seals – crank, countershaft, and ETC. Winderosa Gaskets are extemely high quality US made gasket sets. | |
 |
| Yamaha Blaster Wrist Pin Bearing | $12.95 |
 |
| Yamaha Blaster 200 Hot Rods Connecting Rod– Available in stock stroke. | |
 |
| Yamaha Blaster Hot Rods Crank – Available in Stock or +4mm Stroker. Includes wrist pin bearing. Main bearings not included. | |
 |
| Delta V-Force Reed Cage– The V-Force reed valve system is by far one of the most effective bolt-on performance products you can ever install on your ATV. Gain an average of 3HP in the bottom and midrange, and significant boost in throttle response. | |
 |
 |
||
| Hinson Billetproof Clutch Basket | |
 |
 |
||
| Keihin 28mm PWK Carburetor – Pre-jetted. Note: This price may be higher than you see others selling the same carburetor for but we supply our own titanium needle that was developed for this package. We have never found a needle that Keihin can supply that makes it caurbuerate pefectly. Recommended for the Blasters with stock 200 motors or mild port work. | |
 |
| Keihin 33mm PWK Carburetor – Comes pre-jetted. Recommended for the Blaster 240 Kit ONLY. | |
|
| Keihin 35mm PWK Carburetor – Comes pre-jetted. Recommended for the Blaster 240 Kit ONLY. | |
|
| Keihin 36mm PWK Quad Vent Carburetor – Comes pre-jetted. Recommended for the Blaster 240 Kit ONLY. | |
|
| Yamaha Blaster Pro Design Flow Control – Fits stock to 36mm carburetors. Allows you to adapt larger carbs to your ATV. | |
 |
| Yamaha Blaster UPP Intake Manifold – Fits stock to 36mm carburetors. Allows you to adapt larger carbs to your ATV. | $115.95 |
 |
 |
||
| Fasst 1-1/8″ Flexx Bars – These are the best off road bars money can buy. Bars come with three different elastomers to get the proper cushioning for your type of riding along with a cross bar pad in your color choice of blue, grey, or red. Please Note: 1-1/8″ bar mount kit is required. | $359.95 |
 |
| Streamline Reflex Pro Pack with Clutch and Brake Lever – Available in Black, Blue, Red, and Orange. | |
 |
| Streamline Steering Stabilizer 7-Way Adjustable Non-Rebuildable– Available in Silver, Red, Blue, or Black. | |
 |
| Streamline Steering Stabilizer 7-Way Adjustable Rebuildable– Available in Silver, Red, Blue, or Black. | |
 |
| Streamline Steering Stabilizer 11-Way Adjustable Rebuildable– Available in Silver, Red, Blue, or Black. | |
 |
| Streamline Steering Stabilizer Carbon 11-Way Adjustable Rebuildable– Available in Silver, Red, Blue, or Black. | |
 |
| Pro Design Tether Kill Switch – Available in Black, Blue, or Red | $36.95 |
 |
| CV4 Billet Tether Kill Switch Mount – Handlebar mount for Pro Design and Pro Armor tether kill switches.This mount allows you to mount your switch to the bar without using up all of the spacing. Allows you to mount the switch much closer to the bend. Available in Black and Red. | $49.95 |
 |
 |
||
| Streamline Steel-braided Front Brake Line Kit – (Please specify color & length) Available in black, blue, clear, green, red, or smoke. Some colors and lengths may need to be special ordered. | |
 |
| Streamline Steel-braided Rear Brake Line – (Please specify color & length) Available in black, blue, clear, green, red, or smoke. Some colors and lengths may need to be special ordered. | |
 |
| Billet Brake Line Clamp – 1 pair (Please specify color) Can be used with any 3/4″ or 1″ diameter A-arm. Available in black, blue, red, or silver. | |
 |
 |
||
| Lone Star Racing Axcaliber Axle – Axcalibar Pro Racing Axles are one of the most highly recommended axles on the market for both racers and recreational riders. | $525.00 |
 |
| Dura Blue Heavy Duty Axle – This axle is a recreational level axle thatis twice the strength of the stock axle. It’s a cost effective choice when reliability is a prime concern. | |
 |
| Dura Blue Eliminator X-33 Pin Drive Axle with BILLET Hubs – The X-33 axle uses the same superior material and heat treating as the Eliminator. The unique difference is in the design of the wheel hub mounting area. Standard design ATV axles neck down to about 1″ in diameter. A splined wheel hub slides onto the axle shaft and is retained with a hex nut. As all ATVer’s know, hubs loosen frequently. The X-33 changes all that. The wheel hub is clamped solid and driven by a pin on a 1-3/8″ diameter shaft. This axle is rifled to reduce weight near the rotational axis of the ATV. The X-33 allows for 16 different wheel offset alternatives. | |
 |
| Dura Blue Eliminator X-33 Pin Drive Axle with CAST Hubs – This X-33 axle uses the same design, superior material and heat treating as the X-33 w/ cast hubs. The unique difference is in the wheel hub and that they are billet aluminum for superior strength. |  |
|
